热处理工艺对TC4钛合金冲击磨损性能的影响

研究了退火和固溶时效处理对热轧态TC4钛合金的力学性能和组织的影响,并考察了其冲击磨损性能。结果表明:退火处理后试样组织中转变β相增加,强度、塑性和韧性均较热轧态有所提升;而固溶时效处理后试样组织的晶粒细化且尺寸更为均匀,同时具有最高的强度,而塑性和韧性则较热轧态有所降低。经过10 h的冲击磨损试验后,退火态试样的磨损率最低,而固溶时效态试样的磨损率最高。通过磨损断口观察发现退火态试样表面冲刷犁沟较短,且终点处存在合金的塑性堆积,同时磨损面组织发生塑性变形,晶粒延展拉长。退火态试样较高的塑性和韧性有助于吸收冲击能量,因此表现出较好的耐冲击磨损性能。     

Synergistic effect of glass fibre and Al powder on the mechanical properties of glass-ceramics

To explore the synergistic effect of glass fibre and Al powder on the mechanical properties of glass-ceramics, blast furnace slag was chosen as the main material, and glass fibre and Al powder as reinforcement materials. The phase compositions, microstructures, compressive properties, and apparent density of the glass-ceramics with varying quantities of glass fibre and Al powder were investigated. The experimental results indicated that Al powder could exist as a simple substance in glass-ceramics and form a dense net coating on the surface of blast furnace slag to improve the plasticity of the glass-ceramic. The glass fibre had better reinforcement effect than Al powder because of its extremely high mechanical strength. The plasticity of glass-ceramics, however, severely decreased; the glass-ceramics exhibited brittle failure during compression. A slight increase in the content of CaSi₂ and SiO₂ in the glass-ceramics was closely related to the addition of glass fibre. Considering safety and economy, glass-ceramics with 6% Al and 14% glass fibre (S4) have the best mechanical properties. The compressive strength, strain at maximum force, and apparent density were 40?MPa, 19% and 1.974?g/cm³, respectively.     

Study on the relationship between the particle size distribution and the effectiveness of the K‐powder fire extinguishing agent

The relationship between the particle size distribution and the extinguishing effectiveness of the new K‐powder fire extinguishing agent has been studied experimentally, to explore the reason of the great extinguishing efficiency exhibited by the new K‐powder fire extinguishing agent on Class B fire (liquid fuel fire). The results of the experiment showed that the extinguishing effectiveness increased along with the decrease of the particle size distribution. In addition, a sharp discontinuity appeared around the limiting size, about 40 μm. The powder with the particle size below 40 μm exhibited highly effective extinguishing with the minimum effective extinguishing concentration C_xr = 23 g·m^?3, while the powder with the particle size above 40 μm exhibited little fire extinguishing efficiency. Compared with other fire extinguishing agents produced by different substances, the new K‐powder fire extinguishing has the bigger limiting size. That means, in the same particle size distribution, the new K‐powder fire extinguishing agent contains more highly effective powder than others contain, and is more effective.     

钛与低碳钢的电阻点焊

采用电阻点焊方法对纯钛与低碳钢Q235进行焊接试验，利用扫描电子显微镜观察分析了熔核区组织特性，探讨了焊接电流对熔核尺寸和抗剪载荷的影响. 结果表明，受焦耳热的影响熔核直径随焊接电流的增加而增加，抗剪载荷则随焊接电流的增大而呈先升后降的变化趋势，焊接电流为8 kA时所得接头的抗剪载荷最大，约2.85 kN. 在钢侧熔核区观察到了靠近钢侧厚度约为30～50 μm的TiFe2+α-Fe共晶组织层和粗大TiFe柱状晶；钛侧熔核区主要由靠近钛侧约12 μm厚的TiFe+α-Ti共晶组织层和TiFe柱状晶构成，且观察到了宏观分层现象.     

扩散时间对W在TiAl合金中扩散行为的影响

通过光学显微镜、扫描电镜和硬度测试等分析手段研究了在1250 ℃下扩散保温不同时间对W元素在TiAl合金中扩散行为的影响。结果表明:试样在1250 ℃下进行扩散不同时间后,渗层界面处连接良好,可观察到明显的冶金结合。扩散层厚度随扩散时间的延长而增加,扩散4 h后可得到约15 μm厚的渗层,扩散24 h后可得到约45 μm厚的渗层,此外较长的扩散时间(24 h)可显著改善界面处的裂纹和气孔等缺陷。W在TiAl合金中的扩散机制主要为置换和空位扩散,且W和Ti的原子半径和热膨胀系数等存在差异,使得晶格畸变的出现并进一步阻碍了W元素的扩散。显微硬度试验结果表明W在TiAl合金中进行扩散,可以增强TiAl合金的硬度,且硬度值随W含量的增大而增大。